You can choose your favorite images to see detail drawing instructions:
You can choose your favorite images to see detail drawing instructions:
Today, drawing123.com will guide you how to easily draw a helmet with simple steps.
Let’s get started!
Step 1: Base Rim
Start by drawing a long, slightly curved horizontal shape. This serves as the bottom trim or base of the helmet. It should be narrower at the front (left) and slightly wider toward the back (right).
Step 2: Main Shell
Draw a large, rounded dome starting from the front of the base and arching over to the back. Add a small vertical extension at the front to represent the chin guard area, connecting the dome to the base.
Step 3: Top Vent
Sketch a small, slanted trapezoid shape on the upper front section of the helmet. This will act as the forehead air vent.
Step 4: Visor Outline
Create the main opening for the face by drawing a large, elongated shape that spans across the front and side. The front edge should follow the curve of the helmet’s “face,” while the back curves smoothly toward the middle of the shell.
Step 5: Pivot Point
Draw a small circle near the back edge of the visor. This represents the hinge mechanism that allows the visor to flip up and down.
Step 6: Inner Visor Frame
Define the lens area by drawing a smaller version of the visor shape inside the one created in Step 4. This creates a border or frame around the clear part of the visor.
Step 7: Final Details and Color
Complete the drawing by filling in the different sections. Use a primary color for the main shell, a dark shade for the trim and vents, and a light, translucent tone for the visor lens to give it a glass-like appearance.
Step 1: Base Shell Outline
Draw a simple, rounded dome shape to establish the main shell of the helmet. The bottom edge should curve slightly upwards toward the back.
Step 2: Chin Guard Inner Curve
Define the front-most part of the helmet (on the left) by drawing a smooth curve that defines the inner edge of the chin guard and creates the front opening for the face.
Step 3: Complete the Visor Opening
Finish the frame for the face shield by drawing an upper edge that spans horizontally across the helmet and then curves down on the far side to connect back to the chin guard. This establishes the complete visor opening.
Step 4: Visor Gasket Frame
Add definition to the opening by drawing a thin, parallel frame just inside the opening established in Step 3. This represents the rubber gasket or seal that surrounds the visor.
Step 5: Side Plate Cover
On the right side of the visor opening, add a curved, irregular shape that partially covers the gasket and overlaps the shell. This component is the side plate or base plate, which houses the visor’s rotation mechanism.
Step 6: Ventilation Detail – Forehead
Draw a simple curved line across the forehead area of the shell. This line creates a panel, which will be detailed as an air intake vent.
Step 7: Final Panel Lines
To complete the helmet’s panel structure, draw one final curved line just above the very bottom edge of the helmet. This creates the final section for the bottom trim or base seal.
Step 8: Final Coloring and Shading
With all the structure in place, finalize the illustration by adding color and shading. Typically, the main helmet shell is finished with a vibrant color, while the visor lens, trim, and venting details use darker, contrasting tones to complete the look.
Step 1: Start with the basic inner shape by drawing two concentric rounded U-shapes to form the foundation of the chin and cheek guards.
Step 2: Establish the main dome of the helmet by adding a large, smooth arc that connects the outer top edges of the shapes from the previous step, completing the overall skull cap outline.
Step 3: Begin adding detail to the helmet dome by drawing parallel lines extending from the top of the curve down to the upper line of the inner frame, defining racing or stripe details.
Step 4: Refine the interior trim of the helmet by drawing a clean, continuous inner boundary line that runs parallel along the entire inside of the front opening structure.
Step 5: Complete the helmet’s basic structure by adding a smooth, continuous semi-circular arc that curves below and connects the bottom ends of the cheek guards, forming the chinstrap loop.
Step 6: Finish by defining the colored sections within the outline, including filling the main dome, the stripes, the interior trim, and the chinstrap with their respective solid colors to complete the full vector illustration.
Step 1: Start with the basic profile. Draw a large, rounded helmet shape, like an upside-down ‘U’ that is slightly flattened on the bottom and curves back at the rear, angled in perspective.
Step 2: Define the bottom edge. Draw a clean horizontal line across the base and add a distinct parallel lower trim line, separated by a small gap. The outer lines are now finalized.
Step 3: Begin the graphics. Draw a pair of long, wavy parallel lines, starting from the lower front and curving across the side, ending near the top rear of the helmet.
Step 4: Draw the visor. Define a large visor shape on the front face of the helmet with smooth, continuous lines, including the curved upper edge where it sits against the helmet shell.
Step 5: Add the visor mechanism. Draw concentric circles at the rear pivot point of the visor to detail the attachment mechanism.
Step 6: Insert the top vent. On the crown of the helmet, draw a simple, contoured, elongated diamond-like shape to represent a ventilation port.
Step 7: Complete with color. Fill the main helmet body and bottom section with solid vibrant color. Make the visor opening and the inner part of the vent different solid colors. Fill the racing stripe and the visor pivot ring with distinct colors as well.
Step 1: Start with a slightly wavy horizontal line in the center of the frame. This line defines the bottom front edge of the helmet.
Step 2: Draw a large, high, curved arc that starts from the left end of the original line and ends at the right end. This arc forms the dome shape of the helmet’s main body.
Step 3: Below the bottom center of the helmet shell, add a V-shape. The two legs of the V extend downwards, representing the central portion of the chin strap system.
Step 4: Add two diagonal lines extending from the V-shape towards the left and right edges of the helmet. This creates a Y-shape below the shell, completing the initial structure for the chin straps.
Step 5: Connect the two parallel lines on the left of the chin strap system and the two parallel lines on the right with two more short vertical lines. Then draw a small rectangle over the lower part of the strap intersection to form the basic strap buckle.
Step 6: Draw a small U-shape below the strap buckle to create the strap end.
Step 7: Add a continuous curve starting near the front edge of the helmet shell and sweeping upwards along the inner curve of the dome. This line defines the upper colored panel of the helmet.
Step 8: Add a small, pointed, wing-like shape to the lower front-left area of the helmet shell to represent a vent or design accent.
Step 9: Fill in the helmet with various colors. The main shell is a light blue, and the upper panel is bright yellow. The chin straps are a warm orange-brown, the buckle is a dark charcoal grey, and the side accent vent remains white with its black outline.
Hopefully, this drawing tutorial on Helmet will help you easily create a nice drawing.
