You can choose your favorite images to see detail drawing instructions:
You can choose your favorite images to see detail drawing instructions:
Today, drawing123.com will guide you how to easily draw a scissors with simple steps.
Let’s get started!
Step 1: Start by drawing a long, teardrop shape angled toward the bottom right. This will serve as the first blade of the scissors.
Step 2: Draw a small circle near the rounded top of the blade. This represents the pivot screw that holds the two blades together.
Step 3: Add two short, parallel diagonal lines extending upward from the top of the blade, near the pivot point. These will connect the blade to the handles.
Step 4: Draw a large, slightly irregular circle attached to the right-hand connecting line. This forms the outer edge of the first handle loop.
Step 5: Draw a second large circle to the left of the first one, attached to the left-hand connecting line. The two handles should sit side-by-side above the blade.
Step 6: Inside the right-hand handle, draw a smaller circle to create the finger hole.
Step 7: Inside the left-hand handle, draw another smaller circle to complete the second finger hole.
Step 8: Finally, fill in your drawing with color. Use a metallic shade for the blade and a bright, solid color for the handles to make them stand out.
Step 1: Draw a long, vertical rectangular shape with a rounded top. This will be the first blade of the scissors.
Step 2: Draw a second similar shape, but angle it out toward the right. This creates the open position for the second blade.
Step 3: Add two curved vertical lines descending from the base of the blades to begin the handle structure.
Step 4: On the left side, draw two short, horizontal curved lines. These will act as the “teeth” or grip detail found on some safety scissors.
Step 5: Draw a small circle right where the two blades meet. This is the pivot screw.
Step 6: Draw a large, bulbous circular shape extending from the bottom of the right-side handle line.
Step 7: Draw another large circular shape extending to the left, connecting it to the handle base and the grip detail drawn earlier.
Step 8: Draw a smaller circle inside each of the two large handle shapes to create the finger holes.
Step 9: Color the drawing to finish. Use a light grey for the metal blades and a bright color for the plastic handles.
Step 1: Draw a long, thin rectangular shape with a rounded end pointing toward the upper right. This represents the first blade of the scissors.
Step 2: Add a second similar shape extending toward the lower right, overlapping the base of the first one to create a “V” shape.
Step 3: Place a small circle at the point where the two blades meet. This serves as the pivot screw.
Step 4: Extend two curved lines outward from the top of the pivot point, moving toward the upper left.
Step 5: Complete the upper handle by drawing a large circle that connects to the two lines from the previous step.
Step 6: Draw two more curved lines extending from the bottom of the pivot point toward the lower left.
Step 7: Add a second large circle to complete the lower handle, mirroring the top one.
Step 8: Draw a smaller circle inside each of the two large handles to create the finger holes.
Step 9: Apply solid colors to differentiate the parts: use a metallic shade for the blades and pivot, and a bright color for the plastic handles.
Step 1: Draw a large, slightly irregular oval tilted to the right. This will form the outer edge of the upper handle.
Step 2: Draw a smaller circle inside the first oval to create the finger hole for the handle.
Step 3: Sketch a second large oval directly beneath the first one, overlapping it slightly to form the base of the lower handle.
Step 4: Draw a smaller circle inside this second oval, completing the pair of handles.
Step 5: From the left side of the upper handle, extend a long, pointed triangular shape. This represents the top blade of the scissors.
Step 6: Draw a second pointed triangular shape that starts from the lower handle and crosses behind the first blade, showing the scissors in an open position.
Step 7: Place a small dot or tiny circle in the center where the two blades overlap to represent the pivot screw.
Step 8: Finally, add color to your drawing. Use a bright color for the plastic handles and a metallic grey for the blades and the screw.
Step 1: The Top Blade
Begin by drawing a long, slender, horizontal teardrop shape. This forms the main body of the upper blade, with a pointed tip on the right and a wider, slightly angled base on the left.
Step 2: The Cutting Edge
Add a long, shallow curve along the bottom of the first shape. This line starts near the middle and tapers toward the tip, creating the sharp edge of the blade.
Step 3: The Pivot Screw
Draw a small circle near the wide base of the blade. Add a short diagonal line inside it to represent the screw that holds the two blades together.
Step 4: The Lower Handle Neck
Extend two parallel, downward-curving lines from the bottom-left corner of the blade base. This creates the “neck” that connects the blade to the handle.
Step 5: The Lower Finger Loop
At the end of the neck, draw a large oval. This will serve as the outer frame for the bottom handle loop.
Step 6: The Inner Finger Hole
Draw a smaller oval inside the one from the previous step. This creates the hole where a finger would be inserted.
Step 7: The Upper Handle Neck
Go back to the top of the blade base and draw two more parallel lines, this time curving upward and then out to the left.
Step 8: The Upper Thumb Loop
Draw a large, elongated horizontal oval attached to these new lines. This forms the outer frame of the larger thumb handle.
Step 9: The Inner Thumb Hole
Add a smaller, matching elongated oval inside the top frame to complete the opening for the thumb.
Step 10: Final Details and Shading
Finish the drawing by filling the shapes with a solid color. You can use different tones to distinguish between the metallic blades and the plastic or metal handles for a polished look.
Step 1: Form the first blade
Start with a single, long shape, pointed at one end and slightly rounded at the other. This will be one half of the cutting end of the scissors.
Step 2: Add a hinge
Within this first shape, draw a small circle. This will be the pivot point or screw.
Step 3: Initiate the first handle
Extend two new lines downwards from the rounded end of the blade. This will connect the blade to its handle.
Step 4: Complete the first handle loop
Draw a large loop attached to the two extension lines. This creates the first finger hole of the scissors.
Step 5: Form the second blade
Extend a long line upwards from the other side of the hinge. This establishes the inner cutting edge of the second blade.
Step 6: Form the second handle loop
Similarly, extend two lines downwards from the top of the new blade extension, and then create a large loop, to form the second handle hole.
Step 7: Refine the handles
Finish forming the handle shapes with additional lines, defining the inner holes.
Step 8: Color the finished product
Color your completed scissors. For a realistic look, you can use yellow for the handles and light grey or silver for the blades.
Hopefully, this drawing tutorial on Scissors will help you easily create a nice drawing.
