You can choose your favorite images to see detail drawing instructions:
You can choose your favorite images to see detail drawing instructions:
Today, drawing123.com will guide you how to easily draw a screwdriver with simple steps.
Let’s get started!
Step 1: Draw the Screwdriver Tip Outline
Draw an angled five-sided outline that resembles a sharp, pointed spade or arrowhead at the top left of your page.
Step 2: Extend the Shaft
Extend two long, straight parallel lines diagonally downward from the sides of the tip, connecting them at the bottom with a slightly curved line to form the metallic shaft.
Step 3: Add Details to the Tip Inner Area
Draw a smaller five-sided shape inside the screwdriver tip to create the inner flat surface of the screwdriver blade.
Step 4: Draw the Bolster Ring
Draw a tilted oval shape around the bottom end of the shaft to create the top rim or cap of the handle.
Step 5: Form the Main Handle
Extend the outline down from the oval collar to form a thick cylindrical handle with a rounded bottom, featuring a slight indent near the top for an ergonomic grip.
Step 6: Add Handle Grip Grooves
Inside the handle, draw three long parallel rounded capsule shapes along the length to represent non-slip rubberized grip grooves.
Step 7: Color the Screwdriver
Color the metallic shaft light gray, filling the inner tip detail with dark gray. Color the main body of the handle yellow, the top rim dark yellow, and fill the three grip grooves with a vibrant orange-yellow hue.
Step 1: Draw the Screwdriver Tip
Draw an angled spade shape at the top left of the page, adding a short horizontal line near the flat upper edge to mark the tip’s bevel.
Step 2: Form the Long Shaft
Extend two narrow parallel lines diagonally downward from the bottom of the tip, capping them at the end with a small rounded curve.
Step 3: Draw the Bolster Collar
Draw a thick, rounded donut-like ring around the bottom end of the metal shaft to form the upper guard of the handle.
Step 4: Extend the Handle Sides
Extend two straight, outward-angled lines downward from the bolster collar to outline the body of the handle.
Step 5: Cap the Handle Base
Cap the bottom of the handle with a rounded dome shape, connecting the two side lines together.
Step 6: Add Handle Ridges
Draw two straight parallel lines down the middle length of the handle to create decorative vertical grip panels.
Step 7: Color the Screwdriver
Color the metal shaft light gray. Color the main body of the handle, top collar, and rounded end cap bright red, and shade the vertical grip panels with a slightly darker shade of red.
Step 1: Draw the Base of the Handle
Draw a wide rectangular shape positioned diagonally at the bottom left of the page, rounding off the bottom-left edge to form the base cap of the handle.
Step 2: Add Inner Grip Slots
Draw two long, parallel capsule-shaped slots inside the main handle to outline the non-slip grip inserts.
Step 3: Sketch the Collar Connectors
Add two short, curved outward lines extending from the top corners of the handle base.
Step 4: Form the Handle Cap
Draw a thick, rounded rectangular cap with indented side notches, connecting it directly to the top of the handle base.
Step 5: Add the Shaft Socket Grooves
Inside the top face of the handle cap, draw two small inverted “U” shaped cutouts where the metal shaft will seat.
Step 6: Draw the Shaft and Tip
Extend two long parallel lines diagonally upward to form the long metal shaft, ending with a widened, flat-head screwdriver tip at the top right.
Step 7: Color the Screwdriver
Color the metallic shaft and tip light gray. Color the main handle body, cap, and inner grip slots light teal, and fill the recessed neck section just below the cap with a darker teal shade.
Step 1: Draw the Shaft and Tip
Draw two long horizontal parallel lines extending from left to right. At the far left end, connect them with a pointed, triangular shape to create the screwdriver tip, and close off the inner section with a vertical straight line.
Step 2: Add the Metal Collar
At the right end of the horizontal shaft, draw a small rectangular box attached vertically to cap the end of the shaft.
Step 3: Sketch the Collar Base
Extend a outward-curving bracket shape from the right edge of the small rectangle to form the front flared section of the handle.
Step 4: Form the Main Handle Outline
From the flared front section, draw two long smooth curves tapering out and curving back in toward the right to form a thick, rounded bulb-like handle ending in a smooth curve.
Step 5: Define the Handle Sections
Add two vertical curved lines inside the handle—one near the front neck and one near the back end—to divide the handle into a collar, a main body, and a rear cap.
Step 6: Add Inner Grip Ridges
Draw two concentric elongated oval outlines inside the middle section of the handle to define the contoured rubber grip grooves.
Step 7: Color the Screwdriver
Fill the long shaft and pointed tip with light gray. Color the metal collar near the shaft and the rear cap in dark gray or black. Color the front neck flare, main handle body, and inner grip ridges in bright blue.
Step 1: Draw the Screwdriver Tip
At the bottom left, draw a pointed triangular tip with two small curved indentations on its sides to form a Phillips-head drive end.
Step 2: Extend the Metal Shaft
From the base of the tip, draw two parallel straight lines extending diagonally upward toward the top right, capped with a slight curved line at the top.
Step 3: Add the Collar Guide Ring
Draw an angled oval ring around the top end of the metal shaft to mark the position of the handle collar.
Step 4: Form the Collar Rim
Extend short side lines upward from the oval ring and connect them with a matching curved line to form a thick, disk-shaped collar.
Step 5: Draw the Main Handle Outline
From the top of the collar, extend two long straight lines upward and connect them at the top with a smooth, rounded dome shape to form the handle casing.
Step 6: Add Side Grip Insets
Draw two long vertical lines along the inner sides of the handle, curving outward near the top dome to define the contoured side grip panels.
Step 7: Color the Screwdriver
Color the long shaft and pointed tip gray. Color the collar ring, central strip of the handle, and top dome bright orange. Fill the two side grip panels with dark gray.
Step 1: Draw the Upper Collar
Draw a horizontal rounded rectangle to form the top collar of the handle.
Step 2: Add the Neck Section
Draw two short vertical lines downward from the bottom edge of the collar.
Step 3: Form the Main Handle Body
Draw a long vertical rectangle directly below the neck section, rounding out the bottom end.
Step 4: Add Grip Insets
Draw two narrow, vertical capsule shapes inside the handle body to create texture and grip slots.
Step 5: Draw the Shaft and Tip
Extend two long, straight parallel vertical lines upward from the top collar, ending in a slightly widened flat head tip.
Step 6: Color the Screwdriver
Fill the metallic shaft and tip with gray. Color the middle neck section solid black, and shade the top collar together with the main handle body in bright green. Keep the two inner grip slots black to complete the drawing.
Hopefully, this drawing tutorial on Screwdriver will help you easily create a nice drawing.
